© Baxi Heating U.K. Limited 2009.5122721/03Model 942Inset live fuel effect gas fireIncorporating the VALOR FIRES CONTROLFitted with one of the followi
In the republic of Ireland the installation must be carried out by a competent personand also conform to the relevant parts of:a) The current editio
3.6.2 Any chimney damper or restrictor should be removed. If removal is not possible,they must be secured in the open position.3.7 Fireplace preparati
3.9 Fireplace clearances.3.9.1 The minimum height from the base of the fireplace opening to the underside ofany shelf made from wood or other combusti
Page 13© Baxi Heating U.K. Limited 2009.INSTALLER GUIDEFigure 3. Appliance dimensions and clearances (The fascia may differ from thatshown and dimensi
3.10 Installation options.In the United Kingdom, as supplied, the appliance can be installed in the followingsituations: -3.10.1 Conventional fireplac
3.10.1.1 ‘Hole-in-the-wall’ Installations. It is recommended that a hearth should be installed as in figure 4. If a reduced depth hearth is fitte
3.10.3 Precast concrete or clay flue block system and hearth.The appliance can be installed to aprecast concrete or clay flue blocksystem conforming t
2. The flue must conform to BS 5440: Part 1 in design and installation.The flue, measured from the bottom of the fireplace opening to the bottom of th
4. PACK CONTENTSCarefully remove all the contents. Take special care in handling the ceramic walls andthe ceramic fuel effect. After fitting the slide
Page 19© Baxi Heating U.K. Limited 2009.INSTALLER GUIDEFigure 8. Pack contents
© Baxi Heating U.K. Limited 2009.All rights reserved. No part of this publication may be reproduced in any material form(including photocopying), stor
Page 20© Baxi Heating U.K. Limited 2009.INSTALLER GUIDEFigure 8. Pack contents (continued)Section 2 - ‘Heritage’ model Fascia pack contains:1 Fascia 1
5. FIREPLACE CHECK5.1 Soundness for appliance attachment.Two primary methods of retaining the appliance are provided: -1) By fixing to the fireplace f
6. IGNITION CHECKBefore attempting to install, it is worth checking that the electronic ignition systemperforms satisfactorily.Fit the battery to the
7. GAS SUPPLY CONNECTIONA nut and olive are provided for an 8mm pipe inlet connection to the ‘T’ connector atthe bottom front of the appliance. The ‘T
8. PREPARING APPLIANCE FOR INSTALLATION1. Detach the burner unit from the hotboxby removing two screws (See figure 12).Lift the burner unit clear.2. F
6. There is a length of self adhesive foamseal supplied with the fire. This will need tobe fitted to the outer rear edges of the sideand top flanges o
9. HOTBOX INSTALLATION9.1 Method 1 - Front fixing to fireplace surround.1. If this method of fixing is required thefront flange of the hotbox can be d
insert the hotbox into thefireplace feeding the supply pipethrough the pierced hole in therear grommet.5. The hotbox has two holes ateach side of the
6. Thread the cables through the eyebolts. Return thecables through the holes near the bottom of the hotboxback panel (See figure 20).7. Place the hot
11. Pull each cable taut. Push the cable retainers hard up against the back panel. Theend of the cable adjuster will passinto the hole. Tighten the sc
Page 3Safety First.Valor Fires fires are CE Approved and designed to meet the appropriate BritishStandards and Safety Marks.Quality and Excellence.All
10. BURNER & SUPPLY PIPE INSTALLATION10.1 Burner and supply pipe installation.1. Fit the burner unit to the hotbox with two screws previously remo
10.3 Inlet pressure check.The appliance is pre-set to give the correct heatinput at the inlet pressure shown in section 2 ofthis manual. No adjustment
12. FITTING THE FASCIA12.1 Assembling the ‘Opulent’ fascia(See figure 28).Step 1. Lay the fascia facedown on a flat surface.Step 2. Unscrew and remove
12.2 Assembling the slider control to the ‘Heritage’fascia.1. The fascia is supplied with two brackets secured at thebottom. Lie the fascia face down
4. Align the hole near the bottom of thecontrol linking bar with that in the controlpivot bracket. Join them with the knurledshouldered screw (See fig
14. FRONT / CASTINGS INSTALLATION‘Dream’ model only.1. Place the firefront casting centrally on the hearth in front of the fascia. 2. Place the bottom
position marked on ‘Dream’ models or on ‘Opulent’ and ‘Heritage’ models.Retain in this position to ignite the pilot. The burner should ignite at its l
the room. Keep all doors and windows that open to the outside of the building closed.Check for spillage as above. If an extractor fan is installed in
16. FINAL REVIEW1. COMPLETE THE INFORMATION IN THE WARRANTY AND SERVICE SECTIONOF THE OWNER GUIDE (See last pages of the OWNER guide).2. If a gap is v
17. SERVICING & PARTS REPLACEMENT Always turn off the gas supply before commencing any servicing and allowto cool completely. (The appliance inle
Page 4© Baxi Heating U.K. Limited 2009.INSTALLER GUIDEINSTALLER GUIDEFOR OWNER GUIDE SEE PAGES 47 TO 59
17.1 Checking the aeration setting of the burner.1. The aeration shutter is factory set and should not require adjustment. If the shutteris not as sho
make sure that they are secured firmly to give agood electrical contact.17.4 To remove the fascia.1. Remove the bottom front cover. On the ‘Dream’and
17.5 To replace the control slide unit. 1. Remove the fascia (See section 17.4).‘Heritage’ and ‘Opulent’ models.2. Detach the slide unit by removing t
17.8 To remove the electronic ignition generator.1. Remove the bottom front and fire front castings(See section 17.4).2. Remove the loose ceramic fuel
17.10 To remove the pilot unit.1. Remove the burner unit (See section 17.7).2. Detach the pilot pipe from the pilot unit.3. Detach the thermocouple fr
microswitch but before it has pushed the microswitch leaf against the microswitchbody.When refitting the thermocouple and interrupter block, make sure
17.14 To remove the main burner injector.(See figure 51).1. Remove the burner (See section 17.13).2. Remove the burner clamping screw (See figure 51).
Page 47© Baxi Heating U.K. Limited 2009.OWNER GUIDEOWNER GUIDEFOR WARRANTY AND SERVICE INFORMATIONSEE PAGES 56 TO 59
LIST OF CONTENTSSection PageSAFETY 49APPLIANCE DIMENSIONS 51GAS CONSUMPTION 50OPERATING YOUR FIRE 52The Oxysafe flame sensing & flue blockage s
SAFETYDo have the fire installed by a competent person. In the United Kingdom, installationmust be in accordance with the latest edition of the Gas Sa
CONTENTSSection PageINSTALLER GUIDE 4 - 46OWNER GUIDE 47 - 591. SAFETY AND UNPACKING 72. APPLIANCE DATA AND EFFICIENCY 83. GENERAL INSTALLATION REQU
Do provide a suitable guard that complies with BS 8423 for the protection of youngchildren, the elderly and the infirm. Such a guard is also recommend
APPLIANCE DIMENSIONSPage 51© Baxi Heating U.K. Limited 2009.OWNER GUIDEFigure 2. Appliance dimensions and clearances. (The fascia may differ from that
OPERATING YOUR FIREThe Oxysafe flame sensing & flue blockage safety system.For your safety, this appliance is fitted with a flue blockage safety d
4. For a higher heat level slide the button upwards. The burner flames and heatoutput will gradually increase until the button reaches the high heat p
CLEANING YOUR FIRETo maintain the high performance and quality finish of your fire please follow theseguidelines:Before attempting to clean the fire,
CERAMIC FUEL BED REFITTINGThe installer and owner guide for the ceramic fuel effect is separate from this guide.The installer may have attached it to
WARRANTY AND SERVICEStandard Warranty Terms & ConditionsThe warranty is for 12 months subject to contract.In the United Kingdom servicing can be c
When calling heateam, it would be helpful if you could have the following informationto hand:-1. Fire serial number and fascia code (Located on the in
Page 58© Baxi Heating U.K. Limited 2009.OWNER GUIDEInstaller Details (Block Capitals)Installer NameGas Safe Register or CorgiRegistration Number.Compa
Page 59© Baxi Heating U.K. Limited 2009.D D M M Y YBrand (Please tick)Baxi Valor Wonderfire Other...Date of InstallationFascia
CONTENTS (Continued)Section Heading Page11. CERAMIC WALLS INSTALLATION 3112. FITTING THE FASCIA 3212.1 Assembling the ‘Opulent’ fascia 3212.2 Assem
© Baxi Heating U.K. Limited 2009.
1. SAFETY AND UNPACKINGInstallerBefore continuing any further with the installation of this appliance please read thefollowing guide to manual handlin
drinking in the work area and always wash your hands before eating ordrinking.This appliance does not contain any component manufactured from asbestos
The conversion of net efficiency to gross was achieved by multiplying the netefficiency by the following conversion factor from Table E3 of SAP 2005,
Kommentare zu diesen Handbüchern